Three Bladed Woodworking Precision Knife

Posted by

On October 20, 2026

Design and Construction — a VPOINT router bit tool for CNC routing and nesting, sized for MDF and similar workpieces. The specification table below lists dimensions; the performance data table gives standard reference speeds and feeds to start with, and the FAQ covers selection, parameters and service. ISO 9001 production, batch-verified, custom sizes from drawings.

Design and Construction

The three-bladed woodworking precision knife carries three ground flutes on a tungsten carbide body. Shank diameters (SHK) run 6–22 mm, cutting-edge diameters (CED) 6–20 mm, cutting edge lengths (CEL) 25–102 mm and overall lengths (OVL) 50–150 mm, as listed in the specifications table.

How It Works

Three precision-ground flutes raise the permissible feed at finish quality: each edge takes a thinner chip, so the wall finish holds even at production feed rates. The geometry serves high-volume finish sizing where two-flute bits would slow the line.

Applications

Finish sizing at production feed rates
Visible edge machining on CNC routers
Furniture component production
Panel line finishing passes

Suitable Materials

Solid wood
MDF and melamine-faced panels
Plywood and veneered panels
Laminated boards

Three ground flutes hold finish quality at higher feeds than two-flute geometry.

Material Comparison: Tungsten Carbide vs. PCD

The figures below are typical industry data for CNC tooling. Tungsten carbide is the economic standard for general CNC routing — tough, regrindable and available in every geometry. PCD wins on very high-volume abrasive work; this page covers the carbide line, and the comparison shows where each material wins so you can match the tool to the job.

Property	Tungsten Carbide (This Tool)	PCD Diamond
Hardness	1,500–2,000 HV	7,000–9,000 HV
Tool life on MDF / particleboard / melamine	30–60 h (baseline)	15–20× longer (500–1,200 h)
Tool life on solid hardwood	80–150 h (baseline)	10–13× longer (800–2,000 h)
Edge renewal	4–6 regrinds at shorter intervals	5–8 regrinds, each removing only 0.2–0.3 mm of diamond
Surface finish	Ra ~0.8 μm typical, degrades as the edge wears	Ra ≤ 0.2 μm achievable, stable over the tool life
Thermal conductivity	~80 W/m·K	540–560 W/m·K — heat leaves the edge fast
Friction coefficient	≈ 0.3	≈ 0.05 — lower cutting forces
Fracture toughness	Higher — tolerates interrupted cuts and impacts better	Lower — needs stable, vibration-free setups
Suited for	General-purpose CNC routing in wood, panels, acrylic; the economic standard	Very high-volume abrasive panel work; non-ferrous metals

Figures are typical published values; actual tool life depends on the workpiece material, feed rate, depth of cut, machine condition and maintenance schedule.

Delivery Scope

Single cutter. Order by part number with the shank, cutting-edge diameter and cutting length stated in the specifications table below.

Why Choose VPOINT

One-year warranty on every cutter — defects in material or workmanship are covered for 12 months from delivery.
Custom tooling — diameters, shanks, cutting lengths and flute configurations built to your drawing or sample.
Non-standard fabrication — sizes outside the standard catalogue, including special geometries.
Resharpening service — cutters return to service after regrinding at a fraction of new-tool cost.
Factory-direct since 2008 — ISO 9001 manufacturing in Sichuan and Dongguan, China; no trading intermediaries.

Send a drawing, a sample or a worn tool, and our engineering team will quote the exact specification you need.

Precision & Quality Control

Every cutter is inspected before shipment. Shank diameter, cutting-edge diameter, cutting length and overall length are measured against the values listed in the specifications table, and cutting edge runout is verified on the assembled tool.

Tools measuring outside tolerance do not ship. Inspection is performed under our ISO 9001 quality system, with batch records retained for traceability.

Specifications

Part NO.	SHK	CED	CEL	OVL
10130625	6	6	25	50
10130628	6	6	32	60
10130652	6	6	40	80
10130662	6	6	50	100
10130832	8	8	30	60
10130842	8	8	35	75
10130852	8	8	42	80
1013850	8	8	50	100
10131032	10	10	32	70
10131035	10	10	35	75
10131042	10	10	42	90
10131052	10	10	52	100
10131062	10	10	62	110
10131235	12	12	35	75
10131250	12	12	50	100
10131260	12	12	60	110
10131270	12	12	70	120
10131274	12.7	12.7	42	90
10131275	12.7	12.7	50	100
10131276	12.7	12.7	60	110
10131277	12.7	12.7	70	120
10131278	12.7	12.7	80	130
10131442	14	14	42	90
10131452	14	14	52	100
10131462	14	14	62	110
10131472	14	14	72	120
10131642	16	16	42	90
10131652	16	16	52	100
10131662	16	16	62	110
10131672	16	16	72	120
10131690	16	16	90	150
10131852	18	18	52	100
10131862	18	18	62	110
10131872	18	18	72	120
101318102	18	18	102	150
10132052	20	20	52	100
10132062	20	20	62	110
10132072	20	20	72	120
10132085	20	20	85	140
101320102	20	20	102	150
10132080	20	12.7	80	120
10132280	22	12.7	80	120

Key words: three blade precision knife, 3 flute finish bit, precision end mill, CNC finish cutter, solid carbide end mill, CNC end mill, compression router bit, upcut spiral bit, downcut spiral bit, single flute end mill, two flute end mill, spiral flutes end mill, slotting end mill, profiling end mill, steel slotting cutter, aluminium end mill, acrylic end mill, nano coating end mill, corn milling cutter, edge rounding cutter, flat bottom end mill, ball nose end mill, furniture manufacturing, furniture factory, cabinet making, acrylic sheet, solid wood, particleboard, chipboard, plywood, rubber sheet, rubber board, hardwood, softwood, MDF, HDF, melamine board, laminated board, flycutter, planing bit, surfacing bit, slab flattening bit, bottom cleaning bit, spoilboard leveller, rabbeting bit

Performance Data

Standard reference values for guidance only — always adjust to machine rigidity, clamping and tool wear, and confirm on the actual workpiece.

Material	Typical spindle speed	Typical feed	Notes
MDF	18,000–22,000 rpm	6–10 m/min	Nesting and grooving; watch heat at small diameters
particleboard	16,000–20,000 rpm	5–8 m/min	Reduce feed if the face starts to chip
plywood	16,000–20,000 rpm	5–8 m/min	Keep the compression or shear geometry inside the panel
veneered board	18,000–20,000 rpm	5–7 m/min	Light finish passes protect the veneer
solid wood	15,000–20,000 rpm	4–9 m/min	Grain direction affects finish; climb-cut when possible
hardwood	14,000–18,000 rpm	3–7 m/min	Lower feed in dense grain

Frequently Asked Questions

What finish can I expect on the edge?

With sharp knives and a stable feed the edge comes off clean enough to skip sanding on most boards; test on offcuts first.

How often should I rotate or replace the knives?

Rotate at the first sign of fuzzing or burn; a fresh edge costs less than a rejected panel.

Any special clamping notes?

Seat the knife fully, torque evenly and re-check after the first minute of cutting.

Where do these reference values come from?

They are standard reference ranges for this tool family, compiled from our specification sheets and common workshop practice — always confirm on the actual workpiece.

Sources & standards: ISO 9001 quality management · UNSPSC commodity codes · eClass product classification

Related Search Terms

solid carbide end mill, CNC end mill, compression router bit, upcut spiral bit, downcut spiral bit, single flute end mill, two flute end mill, spiral flutes end mill, slotting end mill, profiling end mill, steel slotting cutter, aluminium end mill, acrylic end mill, nano coating end mill, corn milling cutter