Product Articles

450 mm Hardfacing YD Type CuZnNi Composite Welding Rod: Applications, Materials and Selection Notes

450 mm Hardfacing YD Type CuZnNi Composite Welding Rod - view 5

What this product is. A 450 mm YD-type composite rod: crushed tungsten carbide in a CuZnNi (copper-zinc-nickel) brazing matrix, flux-cored for gas or induction brazing. The matrix wets the carbide at 890-950 C without melting it.

View 450 mm Hardfacing YD Type CuZnNi Composite Welding Rod →

Specification and how to order

Rod information: Item | Specification | Length | 450 mm | Type | YD brazing | Matrix | CuZnNi | Window | 890-950 C |

  • The grade designation and binder content, in writing.
  • Dimensions with the tolerance that actually matters to your grinding or brazing operation.
  • Grain size, where edge sharpness or wear resistance depends on it.
  • Surface condition: as-sintered or ground.
  • Quantity and packing, because small blanks are usually packed by piece count or by weight.

Where it is used

  • Brazing onto drill, mining, road-planing and wear-part bodies.
  • Blanks that are ground into burrs, drills and cutters in a tool room.
  • Pellets and crushed grit for hardfacing and welding consumables.
  • Preforms for press-tool and wear applications.

Handling and storage

  • Carbide is hard but brittle: do not drop blanks or carry them loose in a box.
  • Keep the batch dry, and lightly oiled where a steel carrier or a brazed assembly would corrode.
  • Store by grade and size. Mixing grades in one bin is the most common way a wrong grade reaches the brazing bench.
  • Treat a chipped corner on a ground blank as scrap: it will show up as a defect in the finished tool.

Checks on receipt

  • Measure a sample against the drawing, not against the previous delivery.
  • Look for cracks, chipping and surface porosity under a magnifier.
  • Confirm the grade marking on the box matches the paperwork.
  • Record the batch number so a problem can be traced back to a delivery.

Compared with the alternative

Compared with a finished tool, a blank leaves the grinding to the tool shop: the geometry stays under your control and the grade is chosen for the application, at the cost of an extra grinding step.

From the product comparison section: Two rod routes, two processes – typical industry practice: Factor | YD Brazing Rod (this rod) | Coated Arc Rod | Process | Brazing at 890-950 C | Arc welding with rod | Matrix | CuZnNi flows and wets | Steel matrix fuses | Carbide fate | Preserved – no melt | Partially melted at arc | Best geometry | Bands and skins | Edges and points | Equipment | Braze torch or induction | Welding plant |

Frequently asked questions

Can you supply to a drawing?

Yes. Send the drawing with the grade, the quantity and the tolerance that matters marked, and the quotation will be against that drawing rather than against a catalogue size.

As-sintered or ground?

Both are available. Grinding adds cost and lead time, and is worth it where the blank locates on a ground face or the edge is used without further machining.

What is the minimum order?

It depends on size and grade. Small trial quantities can be agreed before a production order so the grade can be tested in your own process.

Sources and standards

Amana Tool. "Knowledge Base: shank concentricity, collet installation, vibration and sharpening." www.amanatool.com/knowledge_base. Accessed 10 Nov. 2026.
Amana Tool. "Safety Guidelines for Router Bits and Saw Blades." www.amanatool.com/safety. Accessed 10 Nov. 2026.
C.M.T. Utensili. Router bit instruction sheet: collet seating, feed rate and maintenance guidance. Accessed 10 Nov. 2026.

Standards: ISO 9001 · UNSPSC · eClass

Full specifications for 450 mm Hardfacing YD Type CuZnNi Composite Welding Rod · Resources hub · Ask a VPOINT engineer on WhatsApp →

Leave a Reply

Your email address will not be published. Required fields are marked *