Tire Stud Screws in 6/7/8/9/10 mm with Screw-In Fixing: Applications, Materials and Selection Notes

What this product is. Tire stud screws in 6, 7, 8, 9 and 10mm lengths with a tungsten carbide core. The threaded body is the defining feature: the stud is screwed into the tread rather than pressed, which changes both installation and removal.

View Tire Stud Screws in 6/7/8/9/10 mm with Screw-In Fixing →

Specification and how to order

Published specification: Item | Specification | Type | Tire stud screws | Lengths | 6 / 7 / 8 / 9 / 10 mm | Fixing | Threaded screw-in | Core | Tungsten carbide | Supply | Bulk | Inspection | Per-lot thread and length |

• The grade designation and binder content, in writing.
• Dimensions with the tolerance that actually matters to your grinding or brazing operation.
• Grain size, where edge sharpness or wear resistance depends on it.
• Surface condition: as-sintered or ground.
• Quantity and packing, because small blanks are usually packed by piece count or by weight.

Where it is used

• Brazing onto drill, mining, road-planing and wear-part bodies.
• Blanks that are ground into burrs, drills and cutters in a tool room.
• Pellets and crushed grit for hardfacing and welding consumables.
• Preforms for press-tool and wear applications.

Handling and storage

• Carbide is hard but brittle: do not drop blanks or carry them loose in a box.
• Keep the batch dry, and lightly oiled where a steel carrier or a brazed assembly would corrode.
• Store by grade and size. Mixing grades in one bin is the most common way a wrong grade reaches the brazing bench.
• Treat a chipped corner on a ground blank as scrap: it will show up as a defect in the finished tool.

Checks on receipt

• Measure a sample against the drawing, not against the previous delivery.
• Look for cracks, chipping and surface porosity under a magnifier.
• Confirm the grade marking on the box matches the paperwork.
• Record the batch number so a problem can be traced back to a delivery.

Compared with the alternative

Compared with a finished tool, a blank leaves the grinding to the tool shop: the geometry stays under your control and the grade is chosen for the application, at the cost of an extra grinding step.

From the product comparison section: How the fixing route changes service. Typical industry practice: Factor | Screw-In (this stud) | Press-In | Removable Core | Retention mechanism | Thread + rubber | Rubber grip only | Seat + replaceable core | Installation speed | Slower | Fastest | Moderate | Individual replacement | Yes | Difficult | Yes (core only) | Equipment | Screwdriver / tool | Studding gun | Seat tool + core tool | Risk o…

Frequently asked questions

Can you supply to a drawing?

Yes. Send the drawing with the grade, the quantity and the tolerance that matters marked, and the quotation will be against that drawing rather than against a catalogue size.

As-sintered or ground?

Both are available. Grinding adds cost and lead time, and is worth it where the blank locates on a ground face or the edge is used without further machining.

What is the minimum order?

It depends on size and grade. Small trial quantities can be agreed before a production order so the grade can be tested in your own process.

Sources and standards

Amana Tool. "Knowledge Base: shank concentricity, collet installation, vibration and sharpening." www.amanatool.com/knowledge_base. Accessed 10 Nov. 2026.
Amana Tool. "Safety Guidelines for Router Bits and Saw Blades." www.amanatool.com/safety. Accessed 10 Nov. 2026.
C.M.T. Utensili. Router bit instruction sheet: collet seating, feed rate and maintenance guidance. Accessed 10 Nov. 2026.

Standards: ISO 9001 · UNSPSC · eClass

Full specifications for Tire Stud Screws in 6/7/8/9/10 mm with Screw-In Fixing · Resources hub · Ask a VPOINT engineer on WhatsApp →